Nissan QashQai Forums

Consub, I have the ECO facility also but must admit I have not used it as the 160PS + DCT is an absolute dream to drive normally. I have attached a few comments on the ECO Mode but most basically US Nissan Based with a CVT Box but never the less might be of some help - Dave

Eco Mode | NISSAN | TECHNOLOGICAL DEVELOPMENT ACTIVITIES : https://www.nissan-global.com/EN/TECHNO ... eco_m.html
Regarding the Seating I believe you will find this is only on the Tekna + :

So am I right to say that the speedo unit in the Qashqai can be re-calibrated?

Hi Dave Berlin,
I had read all about how the eco mode works, and my query is that when selected there is no indication on the drivers display. I have seen this mentioned by others, and have never seen that question answered. If it is a fault, I will mention it when the car goes in for service. I could try the acceleration on two drives after pushing the switch and see if there is a difference, isolating the fault to the switch or the computer, but reading others comments it seems there may not be much difference. I suspect there is a faulty switch or disconnected wire. I might feed back some comments regarding the handbook as it is not very well written resulting in ambiguities.
The drivers seat entry/ exit feature is only on the automatic and that's what mine is, I suspected that it is only on the memory seats, which are also available on the Tekna as an extra, but it is not clear in the handbook, perhaps it would be better written with clear instructions, replacing the generic "if fitted" notes all over the book.
Regarding the speedo calibration, the dealers have a plug in box that allows them to change the computers wheel size store, amongst other items. this is used by the computer to calculate and display the speedo reading.
I was a development engineer on Concordes engine digital intake control computers in the early 70s. Hence my interest.

ordered the new tekna ,but told only 3 colours available for a new veh
however nisan are stateing this model is going out of production dec 2020
reasons unknown so ive canceled ,my present veh is a 67plate n conecta ,but the contract states
2018 any ideas

helcat wrote: ↑Tue Nov 10, 2020 6:58 pm ordered the new tekna ,but told only 3 colours available for a new veh
however nisan are stateing this model is going out of production dec 2020
reasons unknown so ive canceled ,my present veh is a 67plate n conecta ,but the contract states
2018 any ideas

.
The current J11B is ceasing production because a new version of the Qashqai is being released.
The range has been trimmed down for a month or so, IIRC, there’s a thread about it on here somewhere. There should be some bargains to be had as dealers sell off their stock.
Not entirely sure what your final sentence is about but your number plate being a 67 means the the car was registered between September 2017 and February 2018 - I would guess that your car was first registered in 2018 ?

Helcat, give this a try - Dave

viewtopic.php?f=22&t=10200&start=10

I didn't like the proposed look of the next QQ. It looks like it is going to be more chunky fronted like the Hyundai cars. Instead decided to go for the latest 1.3 Tekna Auto and don't regret it at all. Got a brilliant deal at the local main dealer who was better than the Carwow quote that I was going to use. Only available in black but now have got used to it. Not yet 1000 miles on the clock but it is so much better than the previous 1.2 CVT that we traded in.

Or this - Dave

viewtopic.php?f=21&t=10084

consub wrote: ↑Wed Feb 26, 2020 9:56 pm My wife is short and has difficulty getting in and out, her feet don't reach the ground when swivelling round, she found the n-con easier with 18" wheels, and she prefers the look of them as well. No extras, I will get mats on-line, I use superguard rather than fork out £££££s for the dealer to protect. What date did yours arrive from Nissan? I haven't looked at scuff plates, so now I will

Arn't all the wheels the same diameter around the tyre - the bigger wheels just get thinner rubber?

[ posted in error ]