Sorry for the delay, the car was at service yesterday and I wanted to be 100% sure that the text from the 2019 handbook is the same as in mine, which is the case.
Unfortunately, I had already tried the methods from both handbooks mentioned here without luck.
The sensors are picked up correctly when swapping tires, they are just in the wrong position, so maybe the receivers have been mixed up. I’ll try to contact the Nissan dealer.
Thanks.
TPMS sensor location does not change after rotation
- calnorth
- Posts: 2719
- Joined: Mon Feb 11, 2019 2:01 pm
- Qashqai Model: Mk.2 Qashqai Facelift - J11b (2017–2021)
There is no info on the Nissan TPMS system that I can find. A number of other systems clone sensors to each wheel position which would be useful in the case of a 2nd tyre set. Or replacing a sensor. This situation heads off to a dealer procedure and possibly general tyre fitters?
Cloning appears to simplify ECU TPMS re-configuration..if you had the related TPMS tool?
Cloning appears to simplify ECU TPMS re-configuration..if you had the related TPMS tool?
Mk2 Qashqai Facelift - J11b (2017–and onward)
1.6 Dig-T N-Connecta
1.6 Dig-T N-Connecta
-
- Posts: 1
- Joined: Tue Feb 15, 2022 5:48 pm
- Qashqai Model: Mk.2 Qashqai - J11 (2013–2017)
Hi, I just swapped a front and rear tyre on my 2014 Qashqui and followed the instructions above and the sensors swapped position automatically. I switched on engine with car stationary for 20 mins and then drove a mile or so. When the sensors first activated they were still wrong - but within a few minutes they had swapped to the correct positions.
Hope you change the tyre pressue as the rear ones will need more air in now there at the front.Steve-Cardiff wrote: ↑Tue Feb 15, 2022 5:54 pm Hi, I just swapped a front and rear tyre on my 2014 Qashqui and followed the instructions above and the sensors swapped position automatically. I switched on engine with car stationary for 20 mins and then drove a mile or so. When the sensors first activated they were still wrong - but within a few minutes they had swapped to the correct positions.
-
- Posts: 1
- Joined: Fri Nov 03, 2023 8:29 am
- Qashqai Model: Mk.2 Qashqai Facelift - J11b (2017–2021)
Dfka_dk — how did you resolve it ? I am having the exact same issue
What problem you got ??Pulkitjain87 wrote: ↑Fri Nov 03, 2023 8:33 am Dfka_dk — how did you resolve it ? I am having the exact same issue
-
- Posts: 336
- Joined: Sat Feb 23, 2019 7:27 am
- Qashqai Model: Mk.3 Qashqai - J12 (2021+) New Model
Specifically states in the workshop manual after tire rotation to carry out sensor ID register.
It does not re locate sensors automatically. If it did then there would be no point in setting their positions when carrying out a tpms sensor coding procedure! When coding sensors in you have to set all of their positions if you rotate tyres then you need to carry out ID register which erases all TPMS ID'S and then you have to register them in the order stated on the scan tool.
Once you've done that you need to carry out the calibrate procedure which is in the setting on the HUD, this resets the tempreture reference value also resets the TPMS system.
It does not re locate sensors automatically. If it did then there would be no point in setting their positions when carrying out a tpms sensor coding procedure! When coding sensors in you have to set all of their positions if you rotate tyres then you need to carry out ID register which erases all TPMS ID'S and then you have to register them in the order stated on the scan tool.
Once you've done that you need to carry out the calibrate procedure which is in the setting on the HUD, this resets the tempreture reference value also resets the TPMS system.
-
- Posts: 1
- Joined: Tue Oct 31, 2023 3:04 pm
- Qashqai Model: Mk.1 Qashqai Facelift - J10b (2010–2013)
Ok, we have to go to settings when rotation is needed.lewisbryant wrote: ↑Sun Nov 05, 2023 10:24 am Specifically states in the workshop manual after tire rotation to carry out sensor ID register.
It does not re locate sensors automatically. If it did then there would be no point in setting their find phenq at amazon positions when carrying out a tpms sensor coding procedure! When coding sensors in you have to set all of their positions if you rotate tyres then you need to carry out ID register which erases all TPMS ID'S and then you have to register them in the order stated on the scan tool.
Once you've done that you need to carry out the calibrate procedure which is in the setting on the HUD, this resets the tempreture reference value also resets the TPMS system.
Last edited by NormanL on Mon Nov 13, 2023 7:15 pm, edited 1 time in total.
-
- Posts: 336
- Joined: Sat Feb 23, 2019 7:27 am
- Qashqai Model: Mk.3 Qashqai - J12 (2021+) New Model
You have to have the ID'S re registered their locations using a diagnostic tool/tpms tool then go to settings after rotationNormanL wrote: ↑Mon Nov 06, 2023 9:03 amOk, we have to go to settings when rotation is needed.lewisbryant wrote: ↑Sun Nov 05, 2023 10:24 am Specifically states in the workshop manual after tire rotation to carry out sensor ID register.
It does not re locate sensors automatically. If it did then there would be no point in setting their positions when carrying out a tpms sensor coding procedure! When coding sensors in you have to set all of their positions if you rotate tyres then you need to carry out ID register which erases all TPMS ID'S and then you have to register them in the order stated on the scan tool.
Once you've done that you need to carry out the calibrate procedure which is in the setting on the HUD, this resets the tempreture reference value also resets the TPMS system.